Decibel

decibel
decibel
Unit system	Non-SI accepted unit
Symbol	dB
Named after	Alexander Graham Bell
Conversions
1 dB in ...	... is equal to ...
bel	⁠1/10⁠ bel

The decibel (symbol: dB) is a relative unit of measurement equal to one tenth of a bel (B). It expresses the ratio of two values of a power or root-power quantity on a logarithmic scale. Two signals whose levels differ by one decibel have a power ratio of 10^1/10 (approximately 1.26) or root-power ratio of 10^1/20 (approximately 1.12).^[1]^[2]

The unit fundamentally expresses a relative change but may also be used to express an absolute value as the ratio of a value to a fixed reference value; when used in this way, the unit symbol is often suffixed with letter codes that indicate the reference value. For example, for the reference value of 1 volt, a common suffix is "V" (e.g., "20 dBV").^[3]^[4]

Two principal types of scaling of the decibel are in common use. When expressing a power ratio, it is defined as ten times the logarithm with base 10.^[5] That is, a change in power by a factor of 10 corresponds to a 10 dB change in level. When expressing root-power quantities, a change in amplitude by a factor of 10 corresponds to a 20 dB change in level. The decibel scales differ by a factor of two, so that the related power and root-power levels change by the same value in linear systems, where power is proportional to the square of amplitude.

The definition of the decibel originated in the measurement of transmission loss and power in telephony of the early 20th century in the Bell System in the United States. The bel was named in honor of Alexander Graham Bell, but the bel is seldom used. Instead, the decibel is used for a wide variety of measurements in science and engineering, most prominently for sound power in acoustics, in electronics and control theory. In electronics, the gains of amplifiers, attenuation of signals, and signal-to-noise ratios are often expressed in decibels.

^ Mark, James E. (2007). Physical Properties of Polymers Handbook. Springer. p. 1025. Bibcode:2007ppph.book.....M. […] the decibel represents a reduction in power of 1.258 times […]
^ Yost, William (1985). Fundamentals of Hearing: An Introduction (Second ed.). Holt, Rinehart and Winston. p. 206. ISBN 978-0-12-772690-8. [...] a pressure ratio of 1.122 equals + 1.0 dB [...]
^ Cite error: The named reference clqgmk was invoked but never defined (see the help page).
^ Thompson and Taylor 2008, Guide for the Use of the International System of Units (SI), NIST Special Publication SP811 Archived 2016-06-03 at the Wayback Machine
^ IEEE Standard 100: a dictionary of IEEE standards and terms (7th ed.). New York: The Institute of Electrical and Electronics Engineering. 2000. p. 288. ISBN 978-0-7381-2601-2.

[auto-1] Mark, James E. (2007). Physical Properties of Polymers Handbook. Springer. p. 1025. Bibcode:2007ppph.book.....M. […] the decibel represents a reduction in power of 1.258 times […]

[auto1-2] Yost, William (1985). Fundamentals of Hearing: An Introduction (Second ed.). Holt, Rinehart and Winston. p. 206. ISBN 978-0-12-772690-8. [...] a pressure ratio of 1.122 equals + 1.0 dB [...]

[clqgmk-3] Cite error: The named reference clqgmk was invoked but never defined (see the help page).

[4] Thompson and Taylor 2008, Guide for the Use of the International System of Units (SI), NIST Special Publication SP811 Archived 2016-06-03 at the Wayback Machine

[5] IEEE Standard 100: a dictionary of IEEE standards and terms (7th ed.). New York: The Institute of Electrical and Electronics Engineering. 2000. p. 288. ISBN 978-0-7381-2601-2.

[1]

[2]

[3]

[4]

[5]